A lumber tarp has to cover the load without turning every stop into a wrestling match. Our shortlist starts with a three-piece superlight tarp, then covers related Elohim USA gear for flatbed work.
These picks include flatbed lumber tarps and accessories for other loads. Check the tarp’s size, drop, material, weight, and tie-down points against the cargo you haul.
1. 24 x 18 3PC 15oz Superlight Lumber Tarp
This is a three-piece lumber tarp set with 24-by-18-foot total coverage and an 8-foot drop. Elohim USA describes the material as 14-ounce superlight vinyl and gives the set weight as 60 pounds.
It’s a fit for drivers who want full coverage in separate pieces rather than handling one large tarp. The catalog says it helps protect cargo from rain, wind, dirt, and road debris, and is easier to handle than heavier lumber tarps. Check the dimensions against the full load, especially if lumber lengths extend beyond the covered stack.
See the 24 x 18 three-piece superlight lumber tarp set for the full product details. If your load needs another layout, Elohim USA also carries single-piece 16-by-27-foot lumber tarps with a 4-foot drop.
2. 33" Light Duty Coil Rack for Flatbed Trailers | Steel Coil Cradle
This is a 10-gauge steel cradle for steel coils, wire coils, and other round loads. It’s for flatbed operators hauling coils, not a tarp substitute; it belongs here as related equipment for drivers who handle more than lumber.
The rack works with wood blocks and tie-down straps to help keep coils from rolling during transport. Its black painted finish is stated in the product details. The base variant weighs 36 pounds, and the available quantity choices include four-packs and ten-packs.
3. 40" Combination Winch Bar | Yellow & Gray | Flatbed Truck Tool
This 40-inch forged-steel combination winch bar is for tensioning and releasing flatbed trailer winches. Drivers who handle regular strap work may want a bar on hand to operate standard or low-profile winches.
The catalog gives its weight as 6.1 pounds and describes it as forged steel. Its use cases include daily strap work on flatbeds and step decks. Keep the bar suited to the winch you use, and follow the winch maker’s instructions while tightening or releasing tension.
The yellow-and-gray finish identifies this version. It’s a separate tool from the tarp itself, but it supports the securement work that happens before a covered load leaves the yard.
See the listed details for the Elohim USA 40-inch combination winch bar, made from forged steel and listed in yellow and gray.
4. 40" Ergonomic Combination Winch Bar | Yellow & Gray | Flatbed Truck Tool
This 40-inch forged-steel combination bar has an ergonomic design. It’s aimed at flatbed drivers who spend a lot of time tensioning and releasing winches during their workday.
Elohim USA says its ergonomic shape is designed to reduce wrist and arm fatigue compared with a standard straight bar. The stated weight is 10 pounds. Compare that weight and handle shape with your usual task before choosing between the ergonomic bar and the standard combination style.
Both bars are listed for use with standard and low-profile winches. Fit and safe use still depend on the winch setup and the tool’s proper placement. Don’t use a bar in a way that puts you in the path of a released strap or handle.
5. 40" Heavy Duty Coil Rack for Flatbed Trailers | ASTM A36 Steel
This coil rack is made from 0.275-inch ASTM A36-compliant sheet steel. It’s designed for flatbed operators moving steel, copper, aluminum, or other heavy metal coils.
The catalog lists a black lacquer finish and a product weight of 13.95 pounds. Its stated job is to cradle coils and help prevent them from rolling during transport. Check that the rack suits the coil and trailer setup you use before you load.
A lumber tarp won’t replace coil support equipment. Cargo shape drives the choice: a tarp covers and protects a load, while a coil rack helps cradle a round load. For tarp options beyond the three-piece set, Elohim USA also sells a 20-by-27-foot lumber tarp with a 6-foot drop.
6. 54" Steel Flatbed Pipe Stake | Adjustable
This adjustable pipe stake is made from 8-gauge steel and is designed to fit standard stake pockets. It’s for flatbed haulers who need vertical support to contain cargo or stack materials.
The product details describe its role as load support, not cargo covering. The available quantity choices range from a single stake to larger packs. Confirm that the stake pocket on your trailer fits before ordering.
For an overview of stake-pocket use, our Pipe Stakes for Flatbed Trailers Explained covers the gear category. Cargo securement requirements also depend on the load and its tie-down system. The federal rule at 49 CFR 393.106 sets general securement requirements; check the current rules for your operation.
This stake can support cargo containment, but it doesn’t replace the tie-downs or tarp your load requires.
7. Rubber Coil Cuffs for Flatbed Trailers | Set of 2 | Coil Rack Padding
This set of two heavy-duty rubber cuffs slides over a coil rack to cushion the cradle. It’s for drivers hauling metal coils who want padding between the rack and coil surface.
Elohim USA describes the cuffs as helping protect coil surfaces from scratches, dents, and damage during transport. The listed weight is 4 pounds. The cuffs reduce metal-to-metal contact, but they’re an accessory for a coil rack rather than a stand-alone load support.
Use them when coil surface protection matters during loading and transit. For a fleet, ordering the set as part of the same equipment plan as the rack can help keep the padding matched to the coil-hauling setup.
8. 4" Storable Sliding Truck Winch 5,500 lbs
This heavy-gauge steel winch slides along standard C-track winch rails and locks under strap tension. It’s for flatbed operators who need a movable strap-tensioning point on a compatible rail.
The listed working load limit is 5,500 pounds, and the break strength is 16,500 pounds. Working load limit is the figure to use when checking gear for a load. The federal rule at 49 CFR 393.108 addresses working load limits for cargo securement devices.
Match the winch to the track and strap in your setup. Its role is cargo securement, not tarp coverage.
How to match a tarp and flatbed gear to your load
For lumber, begin with the load’s length and height. Compare the tarp’s coverage and drop with the stack, then check whether the chosen arrangement leaves the sides and ends covered as needed. The three-piece Elohim USA set has an 8-foot drop and 24-by-18-foot total coverage.
Material weight affects handling. The catalog describes the superlight vinyl set as easier to handle than heavier lumber tarps. In general, 14-ounce and 18-ounce tarp materials are common choices; lighter construction can be easier to manage, while a heavier fabric may suit buyers who favor a heavier tarp. The right fit depends on the work and product details, not ounce rating alone.
Water resistance also depends on more than the fabric. Rain can collect at seams or reach worn areas, and abrasion can affect a tarp over time. Don’t treat a quick water test as proof of performance in every storm or on every trip. Check the product information for the exact tarp, inspect it before use, and replace or repair damaged parts as needed.
Look for clear details on tie-down points, such as D-rings or grommets, plus reinforced edges and sewn sections. Those details help you judge how the tarp connects to your load. Ask for the details that matter to your tie-down plan rather than assuming all tarps share the same layout.
Elohim USA ships to all 50 states from its Houston warehouse and works with carriers, fleets, and logistics companies on bulk orders and recurring supply. Shipping rates depend on order weight, dimensions, and destination. For fleet quantities or custom shipping, use the Request a Quote page. You can also browse the tarps and load-protection collection.
Frequently asked questions
What size tarp do I need for a lumber load?
Choose a tarp based on the load’s length, width, and height, including any overhang. Compare those measurements with the tarp’s stated coverage and drop. A 24-by-18-foot set with an 8-foot drop is one option in Elohim USA’s catalog, but it won’t suit every lumber stack. Check coverage against your own load before ordering.
Is a 14-ounce or 18-ounce lumber tarp better?
Neither rating is best for every load. A lighter tarp can be easier to handle, while a heavier option may fit a buyer’s preference for heavier fabric. Compare the whole specification, including size and construction, and check what the maker says about water resistance and care. Don’t use the ounce rating by itself to judge fit.
Are lumber tarps waterproof?
Some tarp materials and designs resist water, but performance depends on the full tarp and its condition. Seams, tie-down points, abrasion, and wear can affect how well a tarp keeps water out. Review the exact product details and inspect the tarp before use. Avoid assuming that a brief water test proves how it will perform on a long trip.
Does Elohim USA offer bulk orders for flatbed equipment?
Yes. Elohim USA works with carriers, fleet operators, and logistics companies on bulk pricing and custom quotes. The company ships to all 50 states from its Houston warehouse. Shipping rates are calculated based on the order’s weight, dimensions, and destination, so request a quote for bulk or freight orders.
For lumber loads, start by matching tarp size and drop to the cargo you haul. Review the 24-by-27-foot lumber tarp with an 8-foot drop or request a quote from Elohim USA for fleet quantities and custom shipping.
